GETTING STARTED WITH PLUMBING BASICS FOR BATHTUB INSTALLATION

Getting Started with Plumbing Basics for Bathtub Installation

Getting Started with Plumbing Basics for Bathtub Installation

Blog Article

Call Today

How do you actually feel about How to Install a Bathtub?


How to Install a Bathtub Yourself
Mounting a bath tub isn't exactly brain surgery, yet it does need strong plumbing, woodworking, as well as in some cases, tiling abilities. Replacing an old bathtub with a brand-new one is likewise a reasonably tough project. If the old tub is readily accessible, the job can relocate rapidly; if you need to open up a wall surface to get rid of the old tub and position the brand-new bathtub, the task is a lot harder. In either instance, the task is within a residence handyman's skills, although you will certainly require a helper to leave the old tub and also set in the new one. Make certain you have actually certified yourself for the job and are comfortable trying it. Rather than employing a contractor to take control of a halfway-completed project, it is better to consider utilizing one prior to you start. Chances are you might need a professional plumber to make tube connections.
This post will assist you install a brand-new bath tub in your restroom if you have actually currently bought a brand-new tub and also don't require to transform the plan of your previous water system pipelines.
Your tools as well as material list ought to consist of the following:
  • New Bathtub

  • Hammer

  • Pipeline Wrenches

  • Prybar

  • Shatterproof glass

  • Level

  • Pliers

  • Adjustable Wrench

  • Putty Blade

  • Screwdriver

  • Cold Knife

  • Measuring tape

  • Pipe Caps


  • Removing Old Taps


    If you require to replace old taps with new ones as a part of your setup, after that the first thing you ought to do is detach the water system. After doing so, activate the taps to drain pipes any kind of water remaining in the system. The process of eliminating the existing taps can be quite problematic due to the limited accessibility that is often the instance.
    Utilize a basin wrench (crowsfoot spanner) or a faucet device to reverse the nut that attaches the supply pipes to the taps. Have a towel all set for the continuing to be water that will come from the pipes. Once the supply pipelines have actually been removed, use the exact same tool to loosen the nut that holds the taps onto the bath/basin. You will require to stop the solitary taps from transforming throughout this process. Once the faucets have been gotten rid of, the holes in the bath/basin will have to be cleansed of any old securing substance.
    Prior to proceeding to fit the brand-new faucets, contrast the pipeline links on the old faucets to the brand-new taps. If the old faucets are longer than the new taps, after that a shank adapter is required for the brand-new faucets to fit.

    Fitting New Taps


    If the tails of the new taps are plastic, then you will require a plastic port to stop damage to the string. One end of the connector fits on the plastic tail of the tap and the other end gives a connection to the existing supply pipes.
    If you need to fit a monobloc, after that you will certainly call for decreasing couplers, which links the 10mm pipeline of the monobloc to the standard 15mm supply pipe.
    Next off, place the faucet in the installing opening in the bath/basin ensuring that the washers remain in location between the tap as well as the sink. Safeguard the faucet in position with the supplier given backnut. As soon as the faucet is safely in place, the supply pipes can be attached to the tails of the taps. The taps can either be connected by utilizing corrugated copper piping or with normal faucet adapters. The former type needs to be connected to the tap finishes initially, tightening only by hand. The supply pipes can later be attached to the various other end. Tighten up both ends with a spanner after both ends have been connected.

    Setting up the Tub


    Utilizing the two wood boards under its feet, put the tub in the required position. The wooden boards are useful in evenly spreading out the weight of the bath tub over the area of the boards rather than focusing all the weight onto 4 little points.
    The next objective is to ensure that the bath tub is leveled all round. This can be achieved by inspecting the level and changing the feet on the tub till the level checks out level.
    To set up faucets, fit the bottom of the furthest adaptable tap port to the suitable supply pipe by making a compression join; then do the very same for the various other tap.
    Switch on the water system and also inspect all joints and also brand-new pipework for leakages and tighten them if essential. Load the tub and additionally check the overflow outlet and also the normal outlet for leaks.
    Ultimately, repair the bath paneling as explained in the manufacturer's user's manual. Tiling as well as sealing around the bath tub needs to wait till the bathtub has actually been made use of a minimum of when as this will settle it into its last placement.

    Planning for the Installation


    To start with, the supporting frame provided with the bathroom needs to be fitted (if called for) according to the producer's instructions. Next off, fit the taps or mixer to the bathtub. When suitable the faucet block, it is essential to ensure that if the faucet comes with a plastic washing machine, it is fitted between the bathroom and also the taps. On a plastic bath, it is likewise practical to fit a sustaining plate under the faucets device to prevent strain on the bathtub.
    Fit the flexible tap connectors to the bottom of the two taps using 2 nuts and olives (in some cases supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and afterwards pass the electrical outlet with the hole in the bath. Make use of the nut provided by the producer to fit the plug-hole. Analyze the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
    Next, fit completion of the adaptable overflow pipe to the overflow outlet. After that, screw the pipe to the overflow face which need to be fitted inside the bath. Make sure you make use of all of the supplied washing machines.
    Attach the catch to the bottom of the waste electrical outlet on the bath tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the trap to the outlet. Attach all-time low of the overflow tube in a comparable manner.The bath should now prepare to be fitted in its final placement.

    Tiling Around the Tub


    In the area where the bath meets the floor tile, it is essential to seal the joins with a silicone rubber caulking. This is necessary as the installation can relocate enough to break an inflexible seal, causing the water to pass through the wall between the bath and the tiling, causing issues with wetness and also feasible leakages to the ceiling listed below.
    You can select from a range of coloured sealants to assimilate your fixtures and installations. They are sold in tubes and also cartridges, and also can sealing voids approximately a width of 3mm (1/8 inch). If you have a bigger void to fill up, you can fill it with twists of soaked newspaper or soft rope. Bear in mind to constantly fill the bathtub with water prior to sealing, to enable the activity experienced when the tub remains in use. The sealant can split relatively very early if you do not think about this activity prior to sealing.
    Additionally, ceramic coving or quadrant ceramic tiles can be utilized to border the bath or shower tray. Plastic strips of coving, which are easy to use and also reduce to size, are additionally quickly available on the marketplace. It is suggested to fit the ceramic tiles making use of waterproof or water resistant glue and cement.

    A Step-by-Step Guide to Installing a Bathtub


    Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.



    But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.



    This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.


    Remove the Existing Bathtub


    To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.



    The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.


    Choose the Right Bathtub


    The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.


    Install the Plumbing and Ledger Board


    You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.



    Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.


    Install the Bathtub


    When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.



    Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.



    If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.


    Hook up the Plumbing


    Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.


    Install the Bathtub Surround


    A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.



    Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.



    If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.



    If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.

    https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/


    How to Install a Bathtub Yourself

    Do you enjoy reading about Tools You Need to Install a New Bathtub ? Give a comment directly below. We would be glad to find out your responses about this post. We hope that you come back again soon. Do you know about another person who is looking into How to Install a Bathtub: Install an Acrylic Tub and Tub Surround? Take a moment to promote it. Thank you so much for your time invested reading it.


    Premium service for plumbing emergencies.

    Report this page